Hyundai spare parts: repair Hyundai: toothed drive belts

1 - a bolt, 20-27 Н•м;
2 - a spring of the mechanism of a tension;
3 - a roller of a tension of a gear belt;
4 - the free party of a gear belt;
5 - a bolt, 80-100 Н•м;
6 - a camshaft pulley;
7 - an adjusting pin; 8 - the party of a tension of a gear belt;
9 - an adjusting label (index) on a forward cover;
10 - an adjusting label on a pulley of a cranked shaft;
11 - a pulley of a cranked shaft.



Removal
PERFORMANCE ORDER
1. Los a bolt of fastening of a pulley of the water pump.
2. Los a bolt of fastening of the generator.
3. Remove a pulley of the water pump and a belt.
4. Remove a pulley of a cranked shaft.
5. Remove a casing of a gear belt.

6. Move a roller of a tension of a gear belt to the water pump and temporarily fix it in this position.
7. Turn out a bolt of fastening of a pulley of a camshaft.
8. Remove a camshaft pulley.
9. Remove a gear belt.

The prevention

Note a direction of rotation of a gear belt for its repeated installation in initial position.
10. Turn out a bolt of fastening of a pulley of a cranked shaft. Remove a pulley of a cranked shaft and the plug.
11. Remove a roller of the mechanism of a tension of a gear belt.



Check
The prevention

Strongly do not bend a gear belt and do not change a direction of its rotation. Do not allow oil and lubricant to contact with a gear belt as it will lead to its destruction.



PERFORMANCE ORDER
1. Check up a gear belt on absence of damages, deterioration, stratification, cracks on teeths and in the basis of teeths, and also on defects at end faces and a belt underside.
2. In the presence of following defects replace a gear belt

Pulleys and roller of the mechanism of a tension of a gear belt
PERFORMANCE ORDER
1. Check up pulleys of distributive and cranked shaft, a roller of the mechanism of a tension and a single pulley on absence of non-uniform deterioration, cracks and damages.
2. Check up ease and smoothness of rotation of a roller of the mechanism of a tension and a single pulley, and also absence of extraneous noise at rotation.



Installation of the mechanism of a tension of a gear belt
PERFORMANCE ORDER
1. Temporarily fix the mechanism of a tension of a gear belt in the taken away position as it is possible more close to the water pump.

2. After installation of the mechanism of a tension adjusting labels on pulleys of distributive and cranked shaft should be combined with indexes.
Turn a cranked shaft of the engine so that the piston of the first cylinder was established in ВМТ in a compression step.



PERFORMANCE ORDER
The prevention

Be convinced, that the plug is established correctly, thus the facet should be from the forward party of the engine.
1. At installation of a pulley of a camshaft the adjusting pin should enter into a pulley aperture.
2. Establish a gear belt so that to exclude its sagging from a tension.

Hyundai spare parts: Dredge Hyundai R290LC-7

To the dress with cars known all over the world company Hyundai lets out the big assortment of tractors and dredges, which as well-known to experts. Technics Hyundai is marked by absence of the big problems in operation, and availability hyundai spare partsю. Engine Cummins QSB5.9-C, weight of 29300 kg, capacity of a ladle 1,27 м3, capacity of the engine of 200 h.p. / 147 kw, 1900 ob./mines, speed 3,1 / 5,2 km/h. We offer minidredges Hyundai, wheel dredges Hyundai, caterpillar dredges Hyundai, face-to-face loaders of various load-carrying capacity. The hinged equipment: hydrohammers, ladles, hydrodistributing, two-maxillary ladles, used hyundai excavator parts, hyundai excavator robex 360 parts, hyundai excavator robex 360 parts list, hyundai excavator parts, hyundai excavator parts list, hyundai truck parts, hyundai heavy duty truck parts.

Hyundai spare parts: Forward cover and the oil pump

1 – a stopper, 40–50 Н•м;
2 – a sealing ring;
3 – плунжер;
4 – a bolt, 12–15 Н•м;
5 – a forward sealing ring;
6 – a forward cover;
7 – an internal gear wheel of the oil pump;
8 – an external gear wheel of the oil pump;
9 – a cover of the oil pump;
10 – a lining;
11 – a lining;
12 – Oil gathering a tube;
13 – a bolt, 15–22 Н•м;
14 – the oil pallet;
15 – the oil filter.

The prevention

At stopper installation it is necessary to use a new sealing ring.
Removal
PERFORMANCE ORDER
1. Remove a gear belt.
2. Turn out all bolts of fastening of the oil pallet.
3. Remove the oil pallet.
4. Remove the oil filter.
5. Remove a forward cover hyundai factory part from the block of cylinders.
6. Remove a cover of the oil pump.
7. Remove internal and external gear wheels of the oil pump from a forward cover, preliminary having noted their mutual position.
8. Turn out a stopper and remove a spring andплунжер.



Check
PERFORMANCE ORDER
1. Check up a forward cover on absence of cracks or damages and if necessary replace it.
2. Check up a forward sealing ring on absence of deterioration or damage of working edges and if necessary replace it.
3. Check up a condition of the oil pallet and if necessary replace it.
4. Check up the mesh oil filter on absence of damages and if necessary replace it.
5. Check up a forward cover on absence of deterioration or damages to places of contact to gear wheels of the oil pump and if necessary replace it.
6. Check up a condition of the safety valve established in a forward cover.
7. Check up the form and absence of damages of a spring of a safety valve.

Length of a spring a free condition: 46,6 mm
Length under loading: 6,1 kg / of 40,1 mm
8. Check up absence of deterioration or damage of teeths of gear wheels of the oil pump.


9. measure a backlash between a gear wheel of the oil pump and a nest in a cover.

Maximum permissible backlash of an external gear wheel of the oil pump: 0,12–0,18 mm


10. measure a hyundai parts catalogue backlash between teeths of gear wheels of the oil pump.

Maximum permissible backlash between teeths of gear wheels of the oil pump: 0,001–0,003 mm
11. By a metal ruler and measure a lateral backlash of gear wheels of the oil pump.

Maximum permissible hyundai factory part lateral backlash of rotors of the oil pump: 0,04–0,06 mm


Installation of a forward cover
PERFORMANCE ORDER


Establish a forward cover with a new hyundai parts catalogue lining and fix bolts, having tightened their demanded moment.

Length of bolts: And – 25 mm; In – 28 mm; With – 45 mm; D – 60 mm; the inhaling moment – 12–15 Н•м



Installation of a forward oil sealing ring
PERFORMANCE ORDER
1. Check up a forward sealing ring on absence of hyundai car parts deterioration or damage of working edges and if necessary replace it.
2. Check up a condition of the spring ring which hyundai parts oem are pressing out working edges of a sealing ring.


3. Grease an external surface of a new sealing ring with engine oil. The special tool 09231–22100 or the plug of hyundai factory part the corresponding diameter establish a sealing ring on a cranked shaft to a contact of a forward cover.
4. The special tool 09231–22000 establish a sealing ring against the stop in a nest of a forward cover


5. Establish a pulley of a cranked shaft, a gear belt and a pulley of a cranked shaft.
6. Establish the oil filter.
7. Clear of the rests of an old lining interfaced original hyundai parts surfaces of the oil pallet and the block of cylinders.


8. Put a continuous layer of hermetic in diameter of 4 mm on an interfaced surface of the oil pallet. Round apertures for bolts hermetic have from the inside. After hermetic drawing it is necessary to establish the pallet no more than in 15 minutes
9. Establish the oil pallet on hyundai parts oem the block of cylinders and fix bolts.

The inhaling moments: 6–8 Н•м



Installation of the oil pump
PERFORMANCE ORDER
1. Establish external and internal gear wheels of the oil pump in a forward cover.
2. Establish a cover of the original hyundai parts oil pump and fix its bolts. After a tightening of bolts be convinced, that gear wheels are turned easily and smoothly.

The inhaling moments: 6–9 Н•м
3. Establish a safety valve, a spring and turn hyundai car parts a stopper, having tightened its demanded moment. Before installation grease a safety valve with engine oil.

The inhaling moments: 40–50 Н•м

Hyundai spare parts: The air filter (ACL)

1 – the resonant chamber;
2 – an inlet air branch pipe;
3 – a cover;
4 – a filtering element of the original hyundai parts air filter; 5 – the case of the air filter;
6 – a bolt, 8–10 Н•м;
7 – a bolt, 4–6 Н•м;
8 – the resonant chamber.


Removal
PERFORMANCE ORDER
1. Remove the inlet air branch pipe hyundai car parts connected to the air filter.
2. Remove a hose of an hyundai parts oe air inlet from the air filter.
3. Remove a cover of the air filter and filtering element hyundai factory part
of the air filter.


4. Turn out bolts and remove the case of the air filter.

Check
PERFORMANCE ORDER
1. Check up the case of the air filter and a cover on absence hyundai parts oe of deformations, corrosion or damages.
2. Check up an air line on absence of damages.
3. Check up the original hyundai parts resonant chamber on absence of deformation or damages.


4. Check up filtering element of the air filter on absence of excessive pollution, damage or hit on it oils. For clearing of a filtering hyundai car parts element use compressed air, hyundai parts catalogue submitting it from the interior of a filtering element. If necessary, replace filtering element of the air filter.
5. Check up the case of the air filter on absence of pollution or damage.

Installation

Installation is spent to hyundai factory part
sequences, return to removal.

Hyundai spare parts: Check of a tension of a gear belt

PERFORMANCE ORDER
1. Turn a cranked shaft in a direction hyundai parts catalogue counter-clockwise hyundai parts oem in position on 90 ° before ВМТ, as is shown in drawing.
The prevention

Be convinced, that valves are adjusted properly.


2. By device BORROUGHS BT-33-73F measure a tension original hyundai parts of a gear belt in the middle of the tension party.

Belt tension on the cold engine of 9,5-16,5 kg
The prevention

Measuring support of the hyundai parts oem device establish in the hyundai car parts basis of teeths of a belt, and a measuring tip - in the middle, from a belt underside

Hyundai spare parts: 2006 -2007 Hyundai Accent Wiring Diagram

Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2006 -2007 Hyundai Accent . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.

Hyundai spare parts: Hyundai Elantra Wiring Diagram and Electrical Troubleshooting (92 - 95)

The Hyundai Elantra (sold in South Korea as the Avante) is a compact car from Hyundai of South Korea launched in 1991. The following wiring diagram and electrical troubleshooting manual apply for Hyundai Elantra 1992 - 1995 model years.

The Elantra electrical system troubleshooting consists of five major diagnostic sections Schematic diagrams, Component location indexes, Harness layouts, Component location, Connector configurations elantra wiring coil. The starting point of each system section is the schematic diagram, these diagrams show how all the components work together, such as electrical current paths Hyundai Wiring diagramme from power Hyundai replacement parts source to used Hyundai parts ground (via electrical load), switch connections at each positions, and other related circuit functions. It is important to fully understand how a circuit work prior to troubleshooting and diagnosis.


Index of Content:

INTRODUCTION
SYMBOLS
TROUBLESHOOTING INSTRUCTIONS
FUSE AND RELAY INFORMATION
POWER DISTRIBUTION
DASH FUSE BOX DETAILS
GROUND DISTRIBUTION
JOINT DISTRIBUTION
AIR BAG
ANTI-LOCK BRAKE SYSTEM
A/C COMPRESSOR CONTROLS
A/T AND IGNITION KEY LOCK CONTROLS
BACK UP LAMPS
BLOWER CONTROLS
BRAKE AND CHARGE WARNING SYSTEM
CHARGING SYSTEM
ClGARETTE LIGHTER
COOLING SYSTEM
COURTESY LAMPS
CRUISE SPEED CONTROL SYSTEM
DASH, CONSOLE AND SWITCH LAMPS
DAYTIME RUNNING LIGHTS (DRL)
DIGITAL CLOCK
DOHC SYSTEM
ELECTRONIC LOCK UP CONTROL SYSTEM
EXTERIOR LAMPS
HEAD LAMPS
HORNS
IGNITION SYSTEM
INDICATORS/GAUGES
PASSIVE SEATBELT SYSTEM
POWER DOOR LOCK
POWER DOOR MIRROR
POWER WINDOWS
SOUND SYSTEM/POWER ANTENNA
STARTING SYSTEM
STOP LAMPS
SUNROOF
TAC SYSTEM
TRUNK LID OPENER
TURN/HAZARD AND LAMPS
VEHICLE SPEED SENSOR
CONFIGURATION OF CONNECTORS
COMPONENT LOCATION
HARNESS LAYOUT

Find detail information about Hyundai Elantra Wiring Diagram and Electrical

Hyundai spare parts: Finding the Perfect Auto Repair Manual

Where Can I Find a Good Repair Manual for My Car?

You need a car repair manual if you want to get access to your vehicles sensor locations, wiring diagrams, used Hyundai parts firing orders, component locator, vacuum diagrams, repair procedures, specific testing and diagnostics for trouble shooting, Hyundai Wiring diagramme steering and suspension information, heating and air-conditioning problems, safety belt , airbag restraint repair, factory bulletins and general information and much more.

We recommend that anyone needing technical repair information should have a quality auto repair manual for their car.

Mitchell1, also called eAutoRepair.net, is one of the best sources for online automotive repair manuals. You will receive access to Hyundai electric parts thousands of pages of comprehensive technical information, complete wire schematics, drive belt routing, diagnostic trouble codes and much more from $11.99

Wiring Schematic Example

How much does it cost?

A typical printed auto repair manual costs between $65.00 and $125.00 dollars, plus you have to wait for it to be Hyundai replacement parts shipped to you, not to mention the extra fee for shipping and handling. Mitchell1 is available for less and you can get access to used Hyundai parts the information right away. The company offers a variety of payment options from $11.99 - Purchase Auto Repair Manual

The advantage of online repair manuals.

1. They cost a lot less than a printed paper manual

2. The content is always updated and new information is added continuously

3. 100% money back guarantee

4. Someone to talk to if you need help with a repair problem.

Conclusion

A great way to get a top quality repair manual Hyundai electric parts for your car is to sign up with an online repair manual provider, such as Mitchell1.

To top it off, you can get the manual right now. Hyundai Wiring diagramme All you need to do is to click on this link. Hyundai replacement parts It will take you to the registration page. To start, just choose what year your car was manufactured.

Hyundai spare parts: Engine repair

1 – a bolt, 23–27 Н•м + to tighten on a corner 60–62 ° + to tighten on a corner 60–62 °;
2 – a head of cylinders;
3 – a lining of a head of cylinders.


Removal
PERFORMANCE ORDER
1. Merge cooling liquid and disconnect the top hose of a radiator.
2. Remove the wide hose located between the air filter and a cover of a head.
3. Remove an air inlet hose.
4. Remove a vacuum hose, a hose of giving of fuel and a hose of a cooling liquid.
5. Remove from spark plugs tips of high-voltage wires.
6. Remove the ignition coil.
7. Remove the air chamber.
8. Remove an inlet collector.
9. Remove the heat-shielding screen and a final collector.
10. Remove a pulley of the water pump and a pulley of a cranked shaft.
11. Remove a casing of a gear belt.
12. Move a roller of a tension of a gear belt to the water pump and temporarily fix it in this position.


13. Remove a gear belt.
14. Remove a cover of a head of cylinders.


15. The special tool 09221-21000 in certain sequence turn out bolts of fastening of a head of cylinders.
16. Remove the rests of a lining of a head of cylinders from the hyundai company oem geneune parts block of cylinders and a head of cylinders.
The prevention

At removal of the rests of a lining be careful, that they have not got to channels of the block of cylinders.



Check
PERFORMANCE ORDER
1. Examine a head of the block of cylinders on absence of damages, cracks, leaks of oil and cooling liquid. If necessary, replace a head of cylinders.
2. Remove a deposit from combustion chambers. Compressed air blow hyundai factory parts channels for greasing.


3. A metal ruler and щупом in six directions check up planeness of a head of the block of cylinders. If necessary a head of the block of cylinders.

The maximum repolishing: 0,08 mm
4. Replace or repair a head of the block of cylinders in the presence of following defects:
– The burnt through saddles of valves;
– Damage of an interfaced surface for installation of inlet and final collectors;
– Damage of nests for installation of oil sealing rings of camshafts.



Installation
PERFORMANCE ORDER
1. Clear interfaced surfaces of the block of cylinders and a head of cylinders.
2. Establish a new lining of a head of cylinders on the block of cylinders.


3. Screw bolts of fastening of a head of cylinders. In certain sequence tighten bolts of fastening of a head of the block of cylinders in a following order:

And. Tighten bolts the moment of an inhaling 23–27 Н•м;
b. Tighten bolts on a corner 60–62 °;
With. Tighten bolts on a corner 60–62 °.
4. Move a roller of a tension of a gear belt to the water pump and temporarily fix it in this position.
5. Establish a gear belt on a camshaft pulley, thus check up, that adjusting labels of pulleys are combined with indexes.
6. Adjust a tension of a gear belt.
7. Establish a cover of a head of cylinders and fix bolts, having tightened their demanded moment.

The inhaling moment: 8–10 Н•м
8. Establish a casing of a gear belt.
9. Establish a new lining of an inlet collector and an inlet collector. Tighten nuts and bolts the demanded moment.

The inhaling moment: 15–20 Н•м
10. Establish a new lining of a final collector and a final collector. Tighten nuts and bolts the demanded moment.
11. Establish the air chamber and fix bolts and nuts, having tightened their demanded moment.

The inhaling moment: 15–20 Н•м
12. Establish the ignition coil.
13. Establish an air inlet hose.
14. Connect a vacuum hose, a hose of giving of fuel and a hose of a cooling liquid.
15. Establish a wide hose.

Hyundai spare parts: Diesel engine Hyundai

The diesel engine Hyundai, considering use of the advanced workings out and technologies in designing, demands the competent approach at carrying out of maintenance service, diagnostics and repair. Only thus it hyundai company oem geneune parts is possible to provide its degree of reliability and to keep technical characteristics at high level, and also to insure itself from not hyundai factory parts planned financial expenses. Our car-care centre renders a full spectrum of services in service of diesel engines Hyundai.

Repair of the diesel engine Hyundai is carried out in the conditions of modern instrumentalno-technical base which allows hyundai parts catalogue to make all kinds of repair of a diesel engine Hyundai in professionally short terms. Presence of the necessary equipment allows to spend both small repair work, and hyundai parts oem complex repair of all engine, including restoration or replacement of all failed spare parts.

Diesel engine repair Hyundai is carried out with observance of the technological parametres defined by schemes of repair. At carrying out of repair work replacement of details of diesel engines Hyundai is made on the certificated spare parts, the qualitative account materials approaching the concrete car also are applied. Upon termination of works the corresponding guarantee is given.

Diagnostics of the diesel engine Hyundai is spent for definition of Hyundai and quality of work of the engine. At carrying out of diagnostic actions various functional methods are used. Computer diagnostics is made by means of the modern system scanner.

Diesel engine diagnostics Hyundai. After carrying out of diagnostics of diesel engines Hyundai mechanics of a diesel site make oringal hyundai parts the plan of repair work of all engine of the car or its details, and also its approximate cost which is served with the automobile owner

Hyundai spare parts: Body

Experts of automobile services will qualitatively spend repair Hyundai of any complexity, beginning from local and before difficult damages of a body. Also painting Hyundai with a guarantee of high quality is offered to the automobile owner.

Hyundai spare parts: Steering.

Both реек Hyundai the special department with own industrial base is engaged in restoration, and repair of helmsmen.

Hyundai spare parts: Descent disorder

Descent disorder. - Disorder Hyundai experts of automobile services apply the specialised computer stand to descent carrying out

Hyundai spare parts: The engine.

At the autonetwork enterprises enough wide experience on repair of internal combustion engines Hyundai is saved up.

Hyundai spare parts: Automatic transmissions

The newest equipment and equipment assumes carrying out of all works on restoration of automatic transmissions Hyundai at high level and with the quality assurance.

Hyundai spare parts: THAT

Maintenance service Hyundai is carried out at presence and replacement of account materials only by the spare parts having the certificate of quality and the control.

Hyundai spare parts: Diagnostic operations

Diagnostic operations are spent for the purpose of drawing up of more exact forecast of the arisen malfunctions of car Hyundai. The automobile owner receives the full list of necessary works on restoration of work of the engine avto and has an opportunity to check repair process.

Hyundai spare parts: Repair Hyundai

Hyundai is a mark of cars is issued by the Korean manufacturers of vehicles. Repair Hyundai has in USA developed enough infrastructure along with active consumption hyundai parts catalogue and acquisition by automobile owners oringal hyundai parts, of motor vehicles of the given mark. The assortment of automobile production of the given manufacturer is huge enough and will satisfy any motorist, release авто from off-road cars to hyundai company oem geneune parts commercial minivens Hyundai is adjusted. Service Hyundai demands the professional approach, therefore the enterprises of an automobile network offer the full list of hyundai factory partsservices in maintenance service and repair of hyundai parts oem vehicles Hyundai. Experts will execute all necessary actions for revealing of malfunctions in work авто, beginning from computer diagnostics and finishing difficult repair.